Get Help Fast

Commercial Generator and Transfer Switch Maintenance

East-West Electric4 min read
Standby generator equipment at a commercial facility

Standby power depends on more than a generator starting. A commercial maintenance review should account for the automatic transfer switch, fuel and starting systems, connected loads, controls, and documented test results. The goal is to determine whether the complete system operates as designed when utility power fails.

Check more than the generator. The automatic transfer switch, fuel and starting systems, connected loads, controls and test results all matter when verifying whether standby power can perform as designed.

For commercial properties around Clearwater, Tampa, and St. Petersburg, a generator maintenance plan should confirm that the equipment can start, transfer the intended loads, and return to normal operation under the conditions for which it was designed.

Understand the Generator and Transfer Switch

The generator supplies the alternate source of power. An automatic transfer switch, or ATS, monitors sources and changes the connected load from normal utility supply to an available alternate source according to the system design and controls. It also helps prevent an unsafe connection between sources.

Not every building requires all circuits to be supplied by a generator. Some facilities prioritize refrigeration, selected HVAC equipment, communications, security, or other business-critical systems. Essential electrical systems in certain occupancies can have additional performance requirements.

A transfer is not necessarily interruption-free. Equipment that cannot tolerate even a short interruption may require other power-conditioning or UPS provisions, based on the application.

Review the Loads Before Maintenance or Upgrades

Make a clear list of the equipment the generator is intended to support. Note motor starting demands, recent tenant changes, added equipment, and any changes to operating hours. The original generator selection may no longer match the property’s current needs.

A qualified electrical team can compare connected and expected loads with the generator, transfer equipment, and distribution system. If an expansion is planned, EWE’s engineering services can help evaluate the electrical scope before equipment is purchased.

Large standby generator enclosures at a commercial property
Large standby generator enclosures at a commercial property.

What a Maintenance Review Should Cover

A facility-specific program can address the generator’s overall condition, batteries and starting system, fuel and cooling components, alarms, controls, electrical connections, and the condition of the transfer equipment. The exact work and intervals depend on the installed equipment and applicable requirements.

For the ATS, qualified personnel may inspect enclosure condition, control indications, contacts or other components as appropriate, and transfer operation using an approved test method. Test records should show whether the complete sequence performed as intended, not just whether the engine started.

Maintain written findings, deficiencies, corrective actions, and retest results. A generator that runs during an unloaded exercise has not necessarily demonstrated how the full standby-power system will perform under the building’s intended load.

Where NFPA 110 and NFPA 70B Apply

NFPA 110 addresses emergency and standby power systems, including sources, transfer equipment, controls, and related components. Its current edition is 2025. The 2026 edition of NFPA 70B addresses broader electrical equipment maintenance and adds a chapter for transfer switches.

Different buildings can face different requirements. The applicable code edition, occupancy, authority having jurisdiction, equipment instructions, and any contractual or regulatory obligations determine what maintenance and testing program applies. Health care facilities may have additional requirements for essential electrical systems and related records.

Prepare for Florida Storm Season Without Guesswork

Coastal moisture, corrosion, severe weather, and long outages make pre-storm maintenance important across Pinellas, Hillsborough, and Pasco counties. Facility managers should confirm which critical operations depend on standby power and where their test documentation is stored. Do not wait for a storm warning to discover an unresolved transfer problem.

If you have noticed an ATS fault or unexplained transfer behavior, review EWE’s automatic transfer switch repair and replacement service. For an installation or system review, see commercial generator services.

Plan the Next Test Around Your Facility

Before scheduling work, gather the generator make and model, transfer switch information, recent maintenance records, critical-load list, and available one-line diagrams. Discuss any interruption-sensitive operations so qualified technicians can plan the work safely.

Contact East-West Electric to discuss generator and transfer switch maintenance or improvements at your Tampa Bay property.

Aerial view of industrial backup power equipment and utility connections
Aerial view of industrial backup power equipment and utility connections.

Common questions

What should a commercial generator maintenance review include?

Review the generator, starting and fuel systems, controls, automatic transfer switch, connected loads and documented test results. A successful engine start alone does not demonstrate full system performance.

What does an automatic transfer switch do?

An automatic transfer switch monitors available power sources and transfers its connected loads between the normal source and an alternate source according to the system design.

Can a standby generator power an entire commercial building?

Only if the generator and distribution system are designed and sized for those loads. Many facilities instead prioritize specified equipment or essential circuits.

How frequently should standby power systems be tested?

Test frequency depends on equipment instructions, the facility type and applicable requirements, which may include NFPA 110. Qualified personnel should follow a documented maintenance and testing plan.

Recent Articles